We are pleased to announce that after over a year in development, our next Locomotive kit , Nutty , should be available this November. Again, like our Greenbat kit, this is a joint project with Harry Billmore . Harry volunteers on the Welshpool and Llanfair railway which was Nutty’s home where it last ran and is one of his favorites .
Our Sixteen Mill model will available as both a kit and a Ready-to-Run locomotive. The kit will feature a pre-assembled , four wheel drive chassis together with many 3D printed parts. The kits being produced using our latest high resolution resin printers.
Bole Laser Craft has just introduced its Trefor quarry wagon as the first of its 7/8 scale garden railway kits.
Cut from premium quality poplar plywood with pre-coloured 3D SLS printed nylon details, this kit makes into a model of the wagons used at the Trefor quarry in North Wales. Kit includes Slater’s 7/8 scale 15 inch wheels to provide a fine looking and running wagon for your 45mm gauge 7/8 scale railway.
Bole Laser Craft is please to announce the first in a range of locomotive kits
Greenbat locomotives were built by Greenwood & Batley Company in Leeds. The company specialised in electric locomotives, particularly battery-powered types for use in mines and other hazardous environments. These were produced in a variety of gauges from 18 inches up to standard gauge.
Our new Greenbat locomotive has been based on one currently working on the Steeple Grange railway in Derbyshire (although some liberties have been taken to allow an eighteen inch gauge to run on 32mm gauge track). The locomotive features four wheel drive from a 12volt micro motor and gearbox. The model runs quite happily on either a 6 or 9 volt battery and is supplied with simple manual control.
We are pleased to announce a new range of 3D printed garden railway wagon couplers suitable for use on small industrial rolling stock.
They are based on “Bell Mouth” couplers as supplied by the likes of Hudsons of Leeds; Orenstein & Koppel and Decauville. As in the prototype, the modeller couples the wagons by first inserting a “link bar” into one coupler mouth and dropping a “T pin” down through a hole in the body to trap the link. The link bar is then inserted into the bell mouth on the next wagon and the other link pin is inserted. This allows the wagon to be both pushed and pulled round tight bends.
To provide compatibility with other makes of coupler; the new Bole Laser Craft coupler may be connecting with a traditional three link chain looped over the top of the “T pin”.
The couplers are Selective Laser Sintered nylon with an attractive “charcoal black” finish. An engineering grade nylon is used to give a tough and compact coupler.
These couplers are included as standard in the new Trefor Quary wagons and are now available separately for the home builder.
The Manor Farm Light Railway speedometer wagon is now available for 45 mm gauge as well as 32 mm gauge.
The opportunity has been taken while altering the chassis to switch to a bolt-on centre buffer coupler. This allows the customer to easily change the supplied coupler to one of their choosing. In addition to a central hole in the buffer beam, a second pair of holes have been included so that an Accucraft chopper coupling can easily be bolted on.
The Manor Farm Light Railway speed wagon is joint venture between Tom Burton (an electronics engineer by profession) and Bole Laser Craft.
The speed wagon contains an on-board computer that constantly monitors the
wagon’s speed via an infra-red detector and wheel mounted encoder. The scale speed is then displayed on a large LED display in the wagon’s roof (this can be selected as either MPH or KPH). The screens brightness can be altered by an underfloor knob.
The computer is powered by 6 AA alkaline (included) or rechargeable batteries. To enable the use of rechargeable batteries a charging socket (compatible with Roundhouse charges and others) is installed together with a “charging” position on the underfloor power switch.
The wagon is an adapted Bole Laser Craft PW department tool wagon (Scheduled for release this autum). The body is laser cut poplar plywood with engraved planks and corner rivet plates. The roofs are hinged so that the operator can get to the batteries when required.
The chassis is constructed from black acrylic with 3D printed sintered nylon axle boxes and leaf springs. 24 mm diameter nylon wheels are fitted on silver steel axles.
Please note that this wagon is only supplied complete and tested, not as a kit.
Currently only available in 32mm gauge (but watch this space )
Bole Laser Craft are delighted to announce that purchasers may now pay via Worldpay. This well-known and trusted system allows customers to pay for their goods using their Visa (both credit and debit), Mastercard , Maestro and JCB cards.
Introducing a range of medium sized SM32 wagon kits based on mining, quarrying and industrial prototypes. The wagons have been scaled to retain their characteristic small size but large enough so their couplings match the 16mm Narrow Gauge Modellers Association’s guideline height used by the live steam locomotive model manufactures (e.g. Roundhouse and Accucraft).
The kits utilise a number of different materials such as poplar plywood, MDF board, brass bearings, steel axles and nylon wheels. The parts have been designed with many “tabs and sockets” so that they are positively located in the correct position whilst the glue sets.
The wagons are modestly priced (£15-£20) so that a descent sized train of wagon should not break the bank. The price has been kept low by excluding some of the more expensive detail parts (e.g. no white metal castings for instance) but not by compromising on running gear or material quality.